2n Analogue UMTS gateway 2N SmartGate UMTS - Manual, Manual do Utilizador Página 1

2N® SmartGate UMTS UMTS + GSM gateway User guide Version 1.1.0 www.2n.cz

Changes 1.2 10 1.2 Changes Manual Version Amendments to Earlier Versions 1.0.0 The User Manual for SmartGate UMTS. 1.0.1 Corrected errors in text

Terms and Symbols Used 1.3 11 1.3 Terms and Symbols Used Manual Symbols Safety n Always abide by this information to prevent persons from injury. W

13 2 2. Description and Installation This section describes the2N® SmartGate UMTS product and its installation. Here is what you can find in t

Description 2.1 14 2.1 Description Packing of 2N® SmartGate UMTS contains UMTS/GSM gateway in white plastic cover, power supply, antenna and cables f

Description 2.1 15 Telephone Line Tones – Operational Tones The UMTS/GSM gateway sends tones to the telephone line to indicate the line status. The t

Description 2.1 16 Dialing end signaling n Only n Dialing reception has been terminated. Connection is being established. PIN tone n n Enter

Before You Start 2.2 17 2.2 Before You Start Product Completeness Check Check the product for completeness before installation please: n 1× 2N® Smar

Before You Start 2.2 18 n 2N® SmartGate UMTS is designed for indoor use. It may not be exposed to rain, flowing water, condensed moisture, fog, etc.

Mounting 2.3 19 2.3 Mounting External Antenna Connection Screw the antenna cable into the SMA antenna connector. Caution n Tighten the antenna conne

The 2N TELEKOMUNIKACE a.s. joint-stock company is a Czech manufacturer and supplier of telecommunications equipment. The product family develope

Mounting 2.3 20 n For backup use only suggested type of accumulators NiMh size AA. Only this type of storage batteries is permitted for use!.When an

Telephone line connection 2.4 21 2.4 Telephone line connection DialThru gateway – basic connection Phone set is normally connected to extension line

SMS Sending Input Connection 2.5 22 2.5 SMS Sending Input Connection You have got a special connector for easy connection to SmartGate UMTS. The conn

23 3 3. Configuration 2N® SmartGate UMTS This section describes configuration of the product 2N® SmartGate UMTS. Here is what you can find in

2N® SmartGate UMTS parameters configuration 3.1 24 3.1 2N® SmartGate UMTS parameters configuration PC Connection You have got a USB cable for PC conn

2N® SmartGate UMTS parameters configuration 3.1 25 Numeric parameters are programmed using numbers in units included in the parameter description. Th

2N® SmartGate UMTS parameters configuration 3.1 26 Installation and setting of SmartGate PCManager (Win7) 1. Connect 2N® SmartGate UMTS to the PC u

2N® SmartGate UMTS parameters configuration 3.1 27 Caution n All tables are filled-in with default values after PCManager start. It is recommended t

2N® SmartGate UMTS parameters configuration 3.1 28 Monitoring Monitoring is active when 2N® SmartGate UMTS is in operation and registered to the UMTS

2N® SmartGate UMTS parameters configuration 3.1 29 Caution n The manufacturer responds to clients' requirements with periodical firmware updati

Table of Contents 1. Product Overview ... 7 1.1 Product Description ...

Table of Parameters 3.2 30 3.2 Table of Parameters All programmable parameters are listed in this section. Each parameter is accompanied with the uni

Table of Parameters 3.2 31 Setting options: YES(1)/NO(0) Default setting: YES Signaling Line reversal indication for call in progress Function No.:11

Table of Parameters 3.2 32 Dial tone – frequency 1[Hz] Function No.: 120 Setting of frequency 1 of dial tone. This tone is generated after Off-Hoo

Table of Parameters 3.2 33 Default setting: 425 Hz Ringback tone – frequency 2 [Hz] Function No.: 127 Setting of frequency 2 of ringback tone. Setti

Table of Parameters 3.2 34 Setting options: 25 / 50 Hz-2N® SmartGate UMTS rings with 50 or 25 Hz on FXS interface Default setting: 50 Hz Ringing sign

Table of Parameters 3.2 35 Telephone interface FXO parameters Dialing parameters Number of rings before Off-Hook Function No.: 200 If 2N® SmartGate

Table of Parameters 3.2 36 Maximal Off-Hook without dialing [s] Function No.: 206 Parameter defines maximal time of line Off-Hook before dialing to

Table of Parameters 3.2 37 Setting options: 1-3400 Hz Setting step: 1 HzD efault setting: 425 Hz Dial tone – frequency 2[Hz] Function No.: 221 Se

Table of Parameters 3.2 38 Reception volume Function No.: 191 See FXS interface parameters. „BabyCall“ – Automatic call BabyCall number Funct

Table of Parameters 3.2 39 n Bar the number to be dialed - the calling subscriber tone; n Route the call to UMTS/GSM network, or to PBX through t

Telephone interface FXO parameters ... 35 FXS routing table parameters ...

Table of Parameters 3.2 40 Caution! n Configuration using phone line programming (DTMF) is applicable for line ‘Other prefixes’ only. Prefix

Table of Parameters 3.2 41 Add Function No.: 396 The Add parameter is used for automatic call routing. A defined string (prefix) is added to t

Table of Parameters 3.2 42 n Accelerate connection establishing by allowing to terminate dialing with a #; n Modify the number to be dialed by remo

Table of Parameters 3.2 43 Off-Hook FXS line and dial PASSWORD plus to activate the function again. Setting options: 0-8 characters (0-9) Defaul

Table of Parameters 3.2 44 End with # Function No.: 494 This parameter enables to establish the call when a # is received. The # character is r

Table of Parameters 3.2 45 FXO line Off-Hook to dial-in timeout [ms] Function No.: 501 Timeout between FXS line Off-Hook and automatic dial in accord

Table of Parameters 3.2 46 Setting options: 0-16 characters (0-9,*,#,+) Default setting: blank Substring Function No.: - Parameter is used t

Table of Parameters 3.2 47 SMS Sending Input Parameters Telephone number for SMS Function No.:600 The telephone number to which an SMS is sent upo

Table of Parameters 3.2 48 Setting options: -According to provider (0) - depending on how the function is selected in the UMTS/GSM network -Activatio

Table of Parameters 3.2 49 ATTENTION - find out if you have to pay for this function. Every check can lower your credit. Setting options: 0-8 charac

6.2 Troubleshooting ... 77 6.3 List of Abbrevi

Table of Parameters 3.2 50 UMTS/GSM operator lock Function No.: - Refer to GSM & SIM Parameters. Time period for GGMC SMS [h] Function No.

Table of Parameters 3.2 51 Global initialization Function No.: 999 Initialization of all 2N® SmartGate UMTS parameters including the PIN and ser

53 4 4. Function and Use This section describes the basic and extending functions of the product 2N® SmartGate UMTS . Here is what you can fi

Voice function 4.1 54 4.1 Voice function Outgoing and incoming call establishing procedures is for illustration described for analog phone connected

Voice function 4.1 55 4. Hang up to terminate the call. The Line LED goes off. If the called subscriber hangs up first, you can hear the busy tone.

Voice function 4.1 56 3. The UMTS/GSM subscriber hears the ringing tone from PBX if the automatic dial in function was applied, if not he hears dial

Voice function 4.1 57 Automatic Call ("BabyCall") If the BabyCall function is enabled on FXS interface, a pre-programmed timeout is counted

Voice function 4.1 58 Configuration of network services 2N® SmartGate UMTS provides some of network services to improve possibility of usage. The co

Voice function 4.1 59 Call forwarding unconditional If activated, incoming calls will be always forwarded to the configured telephone number. Activa

Voice function 4.1 60 Activation for all call types and specified delay time: <Telephone number> <Delay time> Activation fo

Voice function 4.1 61 Call hold Check if your network supports the service before you use it. This service relates to Call waiting described in 0. I

SMS Sending Input 4.2 62 4.2 SMS Sending Input This universal input is intended especially for reporting alarm or error statuses of any equipment pro

Data connection using USB 4.3 63 4.3 Data connection using USB 2N® SmartGate UMTS can be used as high speed wireless modem to connect your PC to inte

Data connection using USB 4.3 64 6. Confirm the saving of your profile (OK). You will be connected to internet automatically. SMS sending and rece

Data connection using USB 4.3 65 APN name must be received from your mobile provider, in example is the APN of T-Mobile Czech republic used. Net

SIM Card PIN protection 4.4 66 4.4 SIM Card PIN protection If a SIM card is PIN-protected and the PIN is not programmed in SmartGate UMTS, UMTS/GSM L

SIM Card PIN protection 4.4 67 Automatic PIN Entering You need not enter the PIN upon power up if it is stored in 2N® SmartGate UMTS – it is entered

69 5 5. Technical parameters This section describes the technical parameters of the product 2N® SmartGate UMTS.

7 1 1. Product Overview In this section, we introduce the 2N® SmartGate UMTS product, outline its application options and highlight the advanta

Technical Parameters 5.1 70 5.1 Technical Parameters Product versions Sierra Wireless Ordering numbers 501428x Sierra Wireless backup version Order

Technical Parameters 5.1 71 Simcom UMTS/GSM SIM card 3V/1,8 plug-in UMTS/GSM module, bandwidth SIM5320E – Euro version UMTS: 900/2100 MHz GSM/

Technical Parameters 5.1 72 Power Supply Battery backup (optional) Telephone Interface FXS (for PBX external line or phone set) Interface type 2-

Technical Parameters 5.1 73 Telephone Interface FXO (for PBX extension line) Interface type 2-wire analog, FXO Telephone connector type RJ 12, 6/2

Technical Parameters 5.1 74 Others Dimensions (w/o connectors) 170 x 130 x 45 mm Operating temperature 0°C to 45°C Operating status signaling 4 LED

75 6 6. Supplementary Information This section describes supplementary information of the product 2N® SmartGate UMTS. Here is what you can fin

Regulations and directives 6.1 76 6.1 Regulations and directives 2N® SmartGate UMTS conforms to the following directives and regulations: n Directiv

Troubleshooting 6.2 77 6.2 Troubleshooting For tips for the solution of other potential problems see faq.2n.cz. ´ No LED is on after power up u Chec

Troubleshooting 6.2 78 ´ 2N® SmartGate UMTS does not communicate with PC u Check the serial cable connection. u Check the COM number setting on PC.

List of Abbreviations 6.3 79 6.3 List of Abbreviations n APN (Access Point Name) Necessary for the GPRS service. n CLIP (Calling Line Identificatio

Product Description 1.1 8 1.1 Product Description Basic Features n The primary purpose of 2N® SmartGate UMTS is to transmit voice between UMTS/GSM n

List of Abbreviations 6.3 80 n SMS (Short Message Service) A term for the system and one unit (message). n SW Software. n TTL (Transistor-Transist

General Instructions and Cautions 6.4 81 6.4 General Instructions and Cautions Please read this User Manual carefully before using the product. Follo

General Instructions and Cautions 6.4 82 Electric Waste and Used Battery Pack Handling Do not place used electric devices and battery packs into

2N TELEKOMUNIKACE a.s. Modřanská 621, 143 01 Prague 4, Czech Republic Tel.: +420 261 301 500, Fax: +420 261 301 599 E-mail: [email protected] Web: www

Product Description 1.1 9 Safety Precautions Do not switch on 2N® SmartGate UMTS in the vicinity of medical apparatuses to avoid interference. The